Description
Product details
Uses Conplast RMC444M1 is used where a high degree of workability and its retention are required, where delays in transportation or placing are likely or when high ambient temperatures cause rapid slump loss. It facilitate production of high quality concrete. Advantages Ready Mixed Concrete- Increased workability and workability retention minimise the risks of long distance deliveries Increased strength - Provides high early strength for precast concrete if water reduction is taken advantage of. Improved quality - Denser, close textured concrete with reduced porosity and hence more durable. Higher cohesion - Risk of segregation and bleeding minimised; thus aids pumping of concrete Chloride free - Safe in prestressed concrete and with sulphate resisting cements and marine aggregates. Standards Conplast RMC444M1 complies with IS:9103:1999 and BS:5075 Part 3 and ASTM-C-494 Type 'F' as a high range water reducing admixture and Type G at high dosage. Description Conplast RMC444M1 is supplied as a brown liquid instantly dispersible in water. Conplast RMC444M1 has been specially formulated to give high water reductions upto 25% without loss of workability or to produce high quality concrete of reduced permeability. Properties Specific gravity 1.20 to 1.21 at 300 C Chloride content Nil. to IS:9103-1999and BS:5075 Air entrainment Approx. 1.5% additional air over control Compatibility : Can be used with all types of cements except high alumina cement. Conplast RMC444M1 is compatible with other types of Fosroc admixtures when added separately to the mix. Site trials should be carried out to optimise dosages. Conplast RMC444M1 is suitable for use with all types of OPC and cement replacement materials such as PFA, GGBFS and microsilica. Workability : Can be used to produce flowing concrete that requires no compaction. Some minor adjustments may be required to produce high workable mix without segregation. Cohesion : Cohesion is improved due to dispersion of cement particles thus minimising segregation and improving surface finish. Compressive strength : Conplast RMC444M1 is primarily highly efficient superplasticiser giving large increase in workability without significant change in compressive strength. Conplast RMC444M1 may be used to produce substantial water reduction resulting in a considerable increase in compressive strength. Durability : Reduction in W/C ratio enables increase in density and impermeability thus enhancing durability of concrete. Application instructions Dosage The optimum dosage is best determined by site trials with the concrete mix which enables the effects of workability, strength gain or cement reduction to be measured. Site trials with Conplast RMC444M1 should always be compared with mix containing no admixture. As a guide, the rate of addition is generally in the range of 0.6 - 1.5 litres /100 kg cement. For any deviations in dosage in special applications, please contact Fosroc Technical Services. Overdosing An over dose of double the recommended amount of Conplast RMC444M1, will result in very high workability and some retardation of setting time will occur. However, the ultimate compressive strength will not be impaired. Dispensing The measured quantity of Conplast RMC444M1 should be added along with the gauging water. For best results, add Conplast RMC444M1 in the last phase after prewetting the mix with 80% of the total water required. Mix design Fosroc has an advisory service on Concrete Mix Design and can be contacted if assistance is required. Conplast® RMC444M1 INDIA/2005/01-120/A Important note : Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard terms and conditions of sale, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that any advice, recommendation specification or information it may give is accurate and correct, it cannot, because it has no direct or continuous control over where or how its products are applied, accept any liability either directly or indirectly arising from the use of its products whether or not in accordance with any advice, specification, recommendation or information given by it. telephone fax e-mail ++91 80-22240018/120 ++91 80-22233474 india@fosroc.com Fosroc Chemicals (India) Pvt. Ltd. Head Office 111/3, Hafeeza Chamber II Floor, K H Road, PBNo. 2744, Bangalore 560027 www.fosroc.com ® Denotes the trademark of Fosroc International Limited Regional Offices Bangalore Mumbai Delhi Kolkata Shankar House, IV Floor 208/209, Persepolis First floor,1/2 East Patel Nagar P-569, Lake Terrace Extn. 1 & 18, RMV Extension Sector 17, Vashi Opp: Vivek Cinema, Main Patel Rd First Floor Bangalore 560 080 Navi Mumbai 400 703 New Delhi 110 008 Kolkata 700 029 Ph:080-2361 3161/2361 2004 Ph:022-2789 6412/14 Ph:011-25884903/4 Ph: 033 24650917 / 55343188 Fax : 080-2361 7454 Fax: 022 - 2789 6413 Fax: 011- 25884422 Fax: 033-24650891 email: Bangalore@fosroc.com email:Mumbai@fosroc.com email:Delhi@fosroc.com email:Kolkata@fosroc.com z Ahmedabad : (079) 26762799 z Ankleshwar :(02646) 220704/224687 z Bhubaneshwar : (0674) 2546415 z Chennai (044) 24899949/24853383 z Chandigarh : (0172) 2639360 z Cochin : (0484) 2356668 z Coimbatore : (0422) 2472966 z Goa : (0832) 2542465 z Guwahati (0361) 2548793 z Hyderabad : (040) 27662324/27662425 z Hubli (0836) 09343402597 z Indore : (0731) 504339/5061477 z Jaipur : (0141) 2235349 z Jamshedpur: (0657) 2223848 z Lucknow :(0522) 2239044 z Nagercoil 09842134873 z Visakhapatnam : (0891) 2564850 / 2707607 Estimating Packing Conplast RMC444M1 is supplied in 5, 20 and 200 litre drums. Storage Conplast RMC444M1 has a minimum shelf life of 12 months when stored under normal temperatures. It should be protected from extreme temperatures and preferably stored in shade. Precautions Health & Safety Conplast RMC444M1 is non-toxic. Any splashes on the skin should be washed immediately with water. Splashes to the eyes should be washed immediately with water and medical advice should be sought. Fire Conplast RMC444M1 is non flammable.
